Which Of The Following Are Characteristic Feature Of High Copper Amalgam Alloy ?
Which Of The Following Are Characteristic Feature Of High Copper Amalgam Alloy ?
Less Marginal # | |
High Creep | |
High Marginal Breakdown | |
Low Compressive Strength |
پاک اسٹڈی لائبریری اپنی خدمات کو بہتر کرنے کے لئے نئے سوفٹ وئیر انسٹال کررہی ہے ۔ اس لئے آئندہ کچھ دن آپ کو کچھ صفحات تک رسائی میں مشکلات کا سامنا ہوسکتا ہے ۔ جس کے لئے ہم معذرت خواہ ہیں۔
Pak Study Library is installing new software to improve its services. herefore, in the next few days, you may face difficulties in accessing some pages. sorry for the inconvenience.
Which Of The Following Are Characteristic Feature Of High Copper Amalgam Alloy ?
Less Marginal # | |
High Creep | |
High Marginal Breakdown | |
Low Compressive Strength |
Which Of The Following Acts As Accelerator In Zinc Oxide Eugenol______
Zn(Oh)2 + Zno | |
Zncl2 + Znso2 | |
Zncl2 + Eugenol | |
Eugenol + Zno |
Which Of The Following Absorbs Maximum Amount Of Water ?
Macrofilled Resin | |
Microfilled Resin | |
Light Cure Activated | |
Hybrid |
Which Material Undergoes Hysteresis ?
Reversible Hydrocolloid | |
Impression Plaster | |
Metallic Oxide Paste | |
Irreversible Hydrocolloid |
Which Material Is The Most Difficult To Remove From The Patients Mouth ?
Impression Plaster | |
Silicone Impression Material | |
Reversible Hydrocolloid | |
Metallic Oxide Paste |
Which Is True Regarding Lathe Cut Silver Alloy______
Has Tensile Strength Both At 15 Min & 7 Days Comparable To High Copper Unicompositional Alloy | |
Achieves Lowest Compressive Strength At 1 Hr. | |
Has Low Creep | |
Requires Least Amount Of Mercury |
Which Is The Use Of Boxing An Impression______
Ease Of Construction Of Denture | |
All Of The Above | |
Ease Of Pouring An Impression | |
Preserving The Sulci |
Which Is The Cement With Adhesive Properties ?
Both B & D | |
Zinc Oxide Eugenol | |
Zinc Polycarboxylate | |
Silicate |
Which Is Not True About High Copper Amalgam Alloys______
Low Hg: Alloy Ratio | |
Low Tensile And Compressive Strength | |
High Tensile Strength | |
Low Creep |
Which Is Not Present In Porcelain______
Silica | |
Calcium Carbonate | |
Amorphous Material | |
Feldspar |
Which Is Gypsum Product______
Plaster | |
Investment | |
Stone | |
All Of The Above |
Which Is Best Material For Rpd Impression______
Impression Plaster | |
Reversible Hydroollioid | |
None Of The Above | |
Irreversible Hydrocolloid |
Which Glass Ionomer Cement Develops Early Resistance To Water Intake On Setting ?
Ceramic Reinforced Glass Ionomer Cement | |
Reinforced Auto Care Glass Ionomer Cement | |
Resin Modified Glass Ionomer Cement | |
Compomer |
Which Component Of Zinc Oxide-Eugenol Cement Gives Its Strength ?
Zinc Acetate | |
Rosin | |
Oil Of Cloves | |
Zinc Oxide |
Which Cement Is Irritating To The Pulp ?
Zinc Phosphate | |
Ethoxybenzoic Acid | |
Zinc Oxide-Eugenol Cement | |
Carboxylate Cement |
Which Cement Base Has The Highest Modulus Of Elasticity ?
Zinc Polycarboxylate | |
Polymer Reinforced Zoe Cement | |
Glass Inomer Cement | |
Zinc Phosphate |
When Two Metals Are Completely Miscible In Liquid State And They Remain Completely Mixed On Solidifiation, The Alloy Formed Is Called______
Eutectic Mixture | |
Solid Solution | |
Peritectic Mixture | |
Inter Metallic Compounds |
When Solid Gets Wet Completely Contact Angle Is______
>90° | |
0 – 90° | |
90° | |
0° |
When Selection The Colour Of Cement To Use For Cementing A Porcelain Jacket Crown, The Powder Being Tested Is Best Mixed With______
Cement Liquid | |
Glycerin-Water Solution | |
Alcohol | |
Only Water |
When Restoring A Tooth With Resin Material, Acid Etching Can Do All Of The Following Except______
Permit Chemical Bonding Between Resin And Enamel | |
Condition The Tooth Surface For Better Wetting | |
Create Surface Irregularities In Enamel For Better Mechanical Retention Of Resin | |
Increase The Surface Area |
When Porcelain Is Basked Against Metal, It Should Possess A______
Linear Coefficient Of Thermal Expansion Greater Than, But Close To That Of The Metal | |
Linear Coefficient Of Thermal Expansion Less Than But Close To That Of Metal | |
High Fusion Temperature | |
High Fusion Expansion |
When Making A Polysulphide Impression For A Caste Crown, Custom Trays Are Usually Preferred Over Stock Trays For All Of The Following Reasons Except____
Custom Trays Facilitate Uniform Contraction Of Impression Material | |
Custom Trays Require Less Impression Material | |
Stock Trays May Be Short In The Flange Area | |
Impressions Made N The Custom Trays Are Easier To Remove From The Mouth |
When Gold Fused With Porcelain Is Fired At Very High Temperature Greenish Discoloration Of Cervical Margin Is Due To______
High Firing Temperature | |
Presence Of Copper | |
Formation Of Excess Oxides | |
Disintegration Of Opaque Layer |
What Is The Working Time Of Zinc Polyacrylate Cement ?
3 Minutes | |
1 Minutes | |
4 Minutes | |
2 Minutes |
What Is The Working Time Of Amalgam?
Three To Four Minutes | |
Five To Six Minutes | |
One To Two Minutes | |
Seven To Eight Minutes |