The Main Ingredient In Dental Plaster In______
The Main Ingredient In Dental Plaster In______
Calcium Sulphate Hemihydrate | |
Calcium Phosphate | |
Calcium Anhydrate | |
Calcium Sulphate Dihydrate |
پاک اسٹڈی لائبریری اپنی خدمات کو بہتر کرنے کے لئے نئے سوفٹ وئیر انسٹال کررہی ہے ۔ اس لئے آئندہ کچھ دن آپ کو کچھ صفحات تک رسائی میں مشکلات کا سامنا ہوسکتا ہے ۔ جس کے لئے ہم معذرت خواہ ہیں۔
Pak Study Library is installing new software to improve its services. herefore, in the next few days, you may face difficulties in accessing some pages. sorry for the inconvenience.
The Main Ingredient In Dental Plaster In______
Calcium Sulphate Hemihydrate | |
Calcium Phosphate | |
Calcium Anhydrate | |
Calcium Sulphate Dihydrate |
The Main Form Of Iron Carbide Found In 18-8 Steel______
Pearlite | |
Austenite | |
Ferrite | |
Martensite |
The Main Difference Between Dental Stone And Dental Plaster Is______
Self Life | |
Chemical Composition | |
Sharpe And Size Of Particles | |
Solubility In Water |
The Main Components Is Sillicophosphate Cement______
Silicate And Gic | |
Zinc Phosphate And Silicate | |
Zinc Phosphate And Gic | |
Zoe And Silicate |
The Main Advantage Of Composites Over Unfilled Direct Filling Resin Is Their______
Lower Thermal Co-Efficient Of Expansion | |
Esthetic Excellence | |
Higher Solubility In Saliva | |
Lower Modulus Of Elasticity |
The Logical Explanation For The Unique Anticariogenic Property Of Most Silicate Cements Is______
The Reduction In Enamel Solubility Due To Fluoride Uptake By Enamel | |
Due To The High Silica Content | |
That Beryllium Flux Is Used In Silicates | |
That Silicates Show Very Little Leakage At The Margins Of The Restoration |
The Linear Solidification Shrinkage Of Type Iv Ni-Cr Based Alloys Is______
1.56% | |
2.30% | |
1.37% | |
3% |
The Latest Method Of Curing Denture Base Resins______
Visible Light | |
Lasers | |
Chemicals | |
Heat |
The Largest Component Of Amalgam Alloy Is______
Silver | |
Tin | |
Copper | |
Zinc |
The Knoop Hardness Number Of Microfilled Composite Restorative Material Ranges From______
15 – 20 Khn | |
40 – 48 Khn | |
50 – 60 Khn | |
25 – 35 Khn |
The Inlay Wax Most Commonly Used For Direct Technique______
Type 1 | |
Type 2 | |
Type 3 | |
Type 4 |
The Impression With The Least Dimensional Change Upon Disinfection Is______
Polysulphide | |
Addition Poly Silicone | |
Agar-Agar | |
Polyether |
The Impression Materials With Lowest Viscosity Is______
Elastomers | |
Agar – Agar | |
Zinc Oxide Eugenol | |
Plaster Of Paris |
The Impression Material Used To Record The Prepared Areas On Abutment Teeth Is______
High Viscosity Elastomeric Impression Material | |
None Of The Above | |
Medium Viscosity Elastomeric Impression Material | |
Low Viscosity Elastomeric Impression Material |
The Impression For A Diagnostic Cast Of A Partial Edentulous Mouth Should Be Taken In______
Impression Wax | |
Modelling Compound | |
Hydro Cal | |
Hydro-Colloid |
The Imperfection Seen On The Lingual Flange Of A Lower Denture Caused By Rapid Heating During A Curing Cycle Is Called______
Surface Porosity | |
Localised Shrinkage Porosity | |
Micro Porosity | |
Gas Inclusion Porosity |
The Ideal Temperature Of Water Bath For Softening Fluid Wax Is About______
51 To 54 Degree C | |
70 To 75 Degree F | |
70 To 75 Degree C | |
51 To 54 Degree F |
The Hygroscopic Technique Is Associated With______
Investment | |
Amalgam | |
Hydrocolloids | |
Silicate |
The Highest Mercury Concentration In Amalgam Filling Is Found______
At The Margin Of The Restoration | |
None Of The Above | |
In The Centre Of The Restoration | |
In The Deepest Part Of The Restoration |
The Higher The Hg Alloy Ratio In Dental Amalgam______
More Gamma 1 Phase Formed | |
More Matrix Matrial Formed | |
Higher The Strength | |
Lower The Creep Value |
The Greatest Stress Which May Be Produced In A Material Such That Stress Is Directly Proportional To The Strain Is Know As______
The Elastic Limit | |
The Yield Strength | |
Modulus Of Elasticity | |
The Proportional Limit |
The Gold Alloys Used For Casting Contain At Least…. Percent Of Precious Metal According To Ada Specification Number 5______
55 | |
75 | |
65 | |
85 |
The Function Of The Coupling Agent In A Restorative Resin Is To Allow______
Bonding Between Filler And Resin | |
Bonding Between Tooth And Resin | |
Bonding Between Filler Crystals | |
Adhesion Of Resin Particles |
The Function Of A Sprue Is To______
Reproduce Fine Detail | |
Form An Opening Of Molten Metal To Enter The Mold | |
Help Polish Cast Restorations | |
Eliminate Air Bubbles On The Wax Pattern |
The Function Of 2% Potassium Sulphate In A Gypsum Product Is______
To Regulate The Setting Expansion | |
Regulate Setting Time | |
Acts As Retarder | |
None |