Which Of The Following Releases Single Wavelength Of Energy ?
Which Of The Following Releases Single Wavelength Of Energy ?
Argon Lasers | |
Led | |
Qth | |
Pac |
پاک اسٹڈی لائبریری اپنی خدمات کو بہتر کرنے کے لئے نئے سوفٹ وئیر انسٹال کررہی ہے ۔ اس لئے آئندہ کچھ دن آپ کو کچھ صفحات تک رسائی میں مشکلات کا سامنا ہوسکتا ہے ۔ جس کے لئے ہم معذرت خواہ ہیں۔
Pak Study Library is installing new software to improve its services. herefore, in the next few days, you may face difficulties in accessing some pages. sorry for the inconvenience.
Which Of The Following Releases Single Wavelength Of Energy ?
Argon Lasers | |
Led | |
Qth | |
Pac |
Which Of The Following Refractory Is Used To Counteract Most Of The Expansion______
Cristobalite | |
Corundum | |
Tridymite | |
Quartz |
Which Of The Following Provide Opacity To Composite ?
Bis-Gma | |
None Of The Above | |
Tegdma | |
Ti02 |
Which Of The Following Properties Of Dental Materials Is Time Dependent______
Elastic Limit | |
Creep | |
Resillience | |
Ultimate Strength |
Which Of The Following Procedure Is Indicated To Produce Cross-Linking In The Polymerization Of Linear Chains Of Acrylic______
Incorporation Of Terminating Agents | |
Addition Of Grain Refining Agents | |
Addition Of Difunctional Monomers | |
Increasing The Amount Of Heat Required For Linear Polymerization |
Which Of The Following Physical Property Can Be Used To Estimate Indirectly The Proportional Limit Of Gold Alloys ?
Rockwell Hardness Number | |
Knoop Hardness Number | |
Brinell Hardness Number | |
Vickerss Hardness Number |
Which Of The Following Phases Of Dental Amalgam Has Minimum Strength______
Epsilon 1 | |
Gamma 2 | |
Gamma 3 | |
Gamma 1 |
Which Of The Following May Result If An Excessive Amount Of Monomer Is Incorporated Into An Acrylic Resin Mixture ?
Low Impact Strength | |
Excessive Expansion | |
Excessive Shrinkage | |
Excessive Brittleness |
Which Of The Following Is Used As Surface Hardener In Impression Material ?
0.2% Potassium Sulfate | |
4% Potassium Sulfate | |
2% Potassium Sulfate | |
2% Sodium Sulfate |
Which Of The Following Is True About Direct Filling Gold______
Whatever May Be The Type Voids Are Inherent | |
Voids Can Be Avoided With Manual Condensation | |
Properly Condensed Mat Gold Has No Voids | |
None Of The Above |
Which Of The Following Is True About Agar Hydrocolloid Impression Material ?
Cannot Register Fine Surface Details | |
Solidfies Between 50 – 70°C | |
Liquefies Between 71 – 100°C | |
Facilitates Fabrication Of Metal Dyes |
Which Of The Following Is The Main Constituent Of Porcelain______
Clay | |
Feldspar | |
Kaolin | |
Quartz |
Which Of The Following Is Present In The Powder Of The Acrylic Resin______
Benzoyl Peroxide | |
Hydroquinone | |
Methyl Methacrylate | |
D-Methyl Paratolouidine |
Which Of The Following Is Not True Of Polymethyl Methacrylate ?
Density Of 1.13 G/Cm3 | |
Tensile Strength Of 60 Mpa | |
Knoop Hardness Number 18 To 20 | |
Modulus Of Elasticity Of 3.4 Gpa |
Which Of The Following Is Not True About Elastomeric Impression ?
Shear Thinning Is Related To Viscosity Of Non Phase Impression Material | |
Single Mix Material Have Higher Viscosity | |
Improper Mixing Of Material Can Cause Permanent Deformation Of Impression | |
Putty – Wash Technique Of Impression Reduces Dimensional Change Of Setting |
Which Of The Following Is Not Affected By Saliva ?
None Of The Above | |
Silicon Impression Material | |
Impression Plaster | |
Impression Paste |
Which Of The Following Is Most Important In Strength Zoe______
Speed Of Mixing | |
Addition Of Few Drops Of Water | |
Temperature Of Mixing Stab | |
Liquid Powder Ratio |
Which Of The Following Is Function Of Fluoride Flux In Soldering Process ?
It Prevents The Formation Of Chromium Oxide Or Dissolves Chromic Oxide Layer | |
It Prevents The Flow Of Material In Undesirable Area | |
Increase The Strength Of Solder | |
It Prevents The Formation Of Copper Oxide |
Which Of The Following Is Correct Regarding Chemical Setting Of Condensation Silicone______
Polymerization Occurs With Elimination Of Single Byproduct | |
By Condensation Of Repeated Molecules Of Monomers | |
Polymerization Occurs With Repeated Elimination Of Small Molecules | |
Condensation Does Not Occur At All |
Which Of The Following Is Correct Glass Transition Temperature Of Impression Compound ?
43.5°C | |
39°C | |
65°C | |
100°C |
Which Of The Following Is Correct Arrangement Of Impression Material Regarding Linear Contraction In Ascending Order ?
Addition Silicone < Polyether < Polysulfide < Condensation Silicone | |
Addition Silicone < Polysulfide < Polyether < Condensation Silicone | |
Condensation Silicone < Polyether < Polysulfide < Addition Silicone | |
Condensation Silicone < Polysulfide < Polyether < Addition Silicone |
Which Of The Following Is Common To Both Zinc Eugenol Cement And Polycarboxylate Cement?
Chemical Bond To Tooth Structure | |
Substitution O Eugenol By Eba To Increase Strength Of Cement | |
Chelation | |
Polyacrylic Acid Is Liquid |
Which Of The Following Is An Example Of A Composite Material ?
Wax | |
Gold Alloy | |
A Filled Resin | |
Colloidal Silica |
Which Of The Following Inhibitor Accelerator System Uses Light Activation Composite ?
Organic Acid-Metal Oxide | |
Organic Acid-Peroxide | |
Peroxide-Amine | |
Diketone-Amine |
Which Of The Following Increases Castability Of Base Metal Alloys______
Beryllium | |
Carbon | |
Molybdenum | |
Tin |