Best Marginal Seal Is Provided By______
Best Marginal Seal Is Provided By______
Zinc Oxide Eugenol | |
Resin | |
Gutta-Percha | |
Zinc Phosphate |
پاک اسٹڈی لائبریری اپنی خدمات کو بہتر کرنے کے لئے نئے سوفٹ وئیر انسٹال کررہی ہے ۔ اس لئے آئندہ کچھ دن آپ کو کچھ صفحات تک رسائی میں مشکلات کا سامنا ہوسکتا ہے ۔ جس کے لئے ہم معذرت خواہ ہیں۔
Pak Study Library is installing new software to improve its services. herefore, in the next few days, you may face difficulties in accessing some pages. sorry for the inconvenience.
Best Marginal Seal Is Provided By______
Zinc Oxide Eugenol | |
Resin | |
Gutta-Percha | |
Zinc Phosphate |
Best Impression Material To Be Used For Securing Impression After Crown Preparation______
Alginate | |
Zno Paste | |
Agar | |
Elastome |
Benzoin Methyl Ether In A Polymer Indicates That They May Be Cured In The Presence Of______
Infrared Light | |
Visible Light | |
Diketone | |
Uv Light |
Before Pouring An Elastic Impression It Is Washed With Slurry Of Water And Stone To______
Increase Gel Strength | |
Wash Off Saliva On Impression | |
Prevent Distortion | |
Prevent Syneresis |
Balanced Stone Is Dental Stone______
Which Undergoes Rapid Expansion | |
In Which Accelerators Or Retarders Have Been Added According To Need | |
In Which Amount Of Water Of Hydration Is Controlled | |
In Which The Crystals Are All Of Uniform Size |
Back Pressure Porosity Can Be Avoided By______
Using Asbestos Linear | |
Placing The Sprue At Least One Quarter Inch Away Form The End Of Casting Ring | |
Using A Short And Wide Sprue | |
Preventing Rapid Heating The Investment In Burnout Oven |
Average Particle Size Of Powdered Gold Is______
0.1 Um | |
30 Um | |
15 Um | |
10 Um |
Austenite Is An Alloy Of Iron Of And Carbon With The Iron In______
Alpha Form | |
Gamma Form | |
Beta Form | |
None Of The Above |
Asbestos Liner Is Used In A Casting Ring To______
Permit Expansion Of The World | |
Retard The Heating Of The Investment | |
Facilitate Venting Of The Mold | |
All Of The Above |
As Per Dna No. 25, Minimum Amount Of Setting Expansion Required For Type V Gypsum Products______
0.15 | |
0.2 | |
0.1 | |
0.05 |
Apart From Composites And Ceramics, Another Material That Could Be Copy Milled Easily And Inexpensively Is______
Titanium | |
Chromium | |
Molybdenum | |
Germanium |
Annealing Is Also Known As______
Stress Relieving Heat Treatment | |
Hard Hardening Treatment | |
Soft Hardening Treatment | |
Precipitating Heat Treatment |
Angles Between Adhesive And Adherent Is Zero Degree, It Indicates______
Irregularities Present Between Adherent Surfaces | |
Rough Surfaces Between Adhesive & Adherent | |
Adherent And Adhesive Molecules Are Tangent To Each Other | |
Complete Wetting Of Surfaces |
Amalgam Restorations Give The Best Clinical Service When The Residual Mercury Content Is______
68-72% | |
38-42% | |
58-62% | |
48-52% |
Amalgam Means______
An Alloy Of Two Or More Metals That Have Been Dissolved In Each Other In The Molten State | |
A Metallic Powder Composed Of Silver, Tin, Copper And Zinc | |
A Metallic Substances In Powder Or Tablet From That Is Mixed With Mercury | |
An Alloy Of Two Or More Metals One Of Which Is Mercury |
Amalgam Achieves 70% Of The Strength By______
4 Hours | |
Hours | |
16 Hours | |
8 Hours |
Along With Polymerisation Shrinkage, One Of The Major Disadvantages Of Polymethyl Methacrylate As Denture Base Resin Are Its Poor______
Esthetic Properties | |
Thermal Properties | |
Biological Properties | |
Mechanical Properties |
All Of The Following Statements Are True For Zinc Oxide Eugenol Cements Except______
Equal Lengths Of Base Paste And Accelerator Paste Are Mixed Together Until The Mix Has A Uniform Colour | |
Both (The mix appear thick at the start of mixing but after 30 seconds of additional spatulation it becomes more fluid) (Water accelerates but heat retards the setting of zinc oxide eugenol cements) | |
The Mix Appear Thick At The Start Of Mixing But After 30 Seconds Of Additional Spatulation It Becomes More Fluid | |
Increase In Temperature And Humidity Shorten The Setting Time |
All Of The Following Statements About Type Ii Silicon Impression Material Are True Except______
They Set By Condensation Polymerisation | |
They Exhibit A Very Low Setting Shrinkage | |
They Evolve Hydrogen When Cast If They Are Not Fully Cured | |
They Have A Lower Tear Resistance Than Polysulphide Rubbers |
All Of The Following Statements About The Differences Between Self-Polymerizing Acrylic Resins And Heat-Cured Resins Are True Except______
The Former Have Higher Residual Monomer Content | |
The Former Are More Porous | |
The Former Have A Lower Molecular Weight | |
The Former Have Greater Transverse Strength |
All Of The Following Statements About Cast Cobalt Alloy Are True Except______
They Have A Lower Proportional Limit Than Gold Alloys | |
They Have A Modulus Of Elasticity Twice That Of Gold Alloys | |
They Are More Rigid Than Gold Alloys | |
They Have Higher Ductility Than Gold Alloys |
All Of The Following Statements About An Alginate Impression Are Except______
It Will Take Up Water And Expand If Kept Wet | |
It Should Be Rapidly Displaced From The Mouth | |
It May Exhibit Fluid Exudates On The Surface As A Result Of Imbibition Of Water | |
It Will Shrink As A Result Of Syneresis |
All Of The Following Is Used As Accelerator In Zinc Oxide Eugenol Cement Except______
Calcium Chloride | |
Bromoglycerine | |
Zinc Acetate Dehydrate | |
Acetic Acid |
All Of The Following Can Be Used To Slow Down The Setting Of Zinc Oxide Eugenol Impression Paste Except______
Adding A Small Amount Of Water | |
Cooling Mixing Slab | |
Adding A Small Amount Of Glycerine | |
Altering The Amounts Of The Two Pastes Used |
All Of The Following Are True For Traditional Solution Liner, Except______
It Is Not Necessary In Moderately Deep Cavities Under Glass Ionomer Restoration | |
Have Film Thickness Of 1 – 50 Microns | |
Protect The Pulp From Reaction Products Leaching Out Of Restoration | |
Do Not Provide Thermal Or Electric Insulation |